Saturday, January 12, 2013

Starting to build the superstructure

I have made some more good progress on the the build.  

First, here is a picture of the Bow Eye installation.  I put in some biax fiberglass and then epoxied in an aluminum backer plate.  Hopefully, the bow eye will never be an issue.


 Next, I started working on the sheer decks (gunnels) and the front anchor locker.  Instead of putting in a typical anchor splashwell that most Tolman style skiffs had, I put in a full anchor locker.  I am using an anchor windlass with an anchor well to hold around 300 feet of rope and around 20 feet of chain.  I made the typical splashwell a solid deck that the windlass will mount onto.
Here is the anchor pulpit.  I have anchor roller that I will be using.  Here is a picture of that.


I built the anchor pulpit out of 1-1/2" Meranti plywood glassed with biax.

Here I am installing the sheer decks and anchor deck.


Here is a picture of the bow, looking up at the anchor deck.

I have decided that at least for now, I am just going to go with a single, 2" thick gunnel on the fishing deck.  If I need to, I will install a bolster cushion of some sort, but right now, it feels pretty good on the thighs.



Here is the sheer decks after glassing and trimming.  I just used a flush trim router bit a and flush trimmed on the inside.


I just used a laser level at the correct height to locate the height of the top of the collision locker and bunks, then traced with a Sharpie.

Here is a picture of the collision bulkhead after installing.



I painted the inside of the collision chamber with Glidden Polyurethane Porch paint while the access was easy.  



Here is the top of the collision chamber, taped and ready for final epoxy. I decided to use a simple drop in deck plate to allow access for storage in the collision locker.

Here is the fiberglass drain tube i put in at the bottom of the collision chamber.


Finally, here is the collision chamber, completed.   

I also marked out the location of my aft cuddy bulkhead and aft pilot house bulkhead.  I will be making the aft cuddy bulkhead tomorrow.

Friday, December 28, 2012

A lot of little things accomplished....

Well, the last month has resulted in a lot of little jobs getting completed.

After getting the boat flipped over, I had to level out the jig and put some v shaped forms underneath to set the boat on.  Then I could get to work on finishing the inside of the bare hull.

First up was fiberglassing all the interior seams, and there are a lot!  I had to fiberglass the chine/side seams, the transom seams, the stringers to the bottom and finally the tops and sides of the stringers.

This was done with heavy fillets followed buy 4 inch tape, 6 inch biax tape and 8 inch tape.  Around 200 feet of fiberglass tape in all.










Fiberglassing of all the interior seams took the better part of two days.  I ended up with a lot of bubbles that i had to repair.  Most of the larger ones I filled with epoxy with a syringe and a large needle.  The smaller ones I just left.

With that out of the way, I moved on to filling in all the screw holes from installing the front bow panels.  You can see all the white dots, this was from using silica thickened epoxy.




Now it was time to drill a very large hole in the boat.  It was time to install the main drain for the boat.  I made a drain tube by wrapping fiberglass around a PVC pipe covered in wax paper to get an exact 15/16" inside diameter.


I used a 1-1/8" hole saw so I would have room for some epoxy filler.

I drilled the hole most of the way through from the inside first, then when the pilot bit broke through on the outside, I started from the outside so the hole saw would not "blow out" badly.  I started the outside hole by running the holesaw in reverse and it started very smoothly.






After that, I just filled with epoxy.  Came out great.

Next I drilled the holes for the front bow eye and sealed the inside with epoxy.  It should be a solid bow  eye, it is 1/2" 316 stainless.


Tomorrow I am going to wash the inside with ammonia and then put on a couple of final coats of epoxy on the entire inside of the hull.  Today I went and picked up the MDO plywood I am using to build the inside structure.  After I get through putting on the final epoxy coats on the inside of the hull, I am going to start building the inside, starting at the front.  Hopefully there will be some good progress in the next couple weeks.

Wednesday, November 28, 2012

We got the boat flipped over and sitting upright

Well, last week we got the boat flipped over and sitting upright.  I decided to use 4 chain hoists on my A frame lifts instead of having a bunch of people come over.  I figured someone would have too much to drink and end up getting crushed under the boat!

Well, I didn't take any pictures of the actual flip, because I was trying to do it by myself and I was nervous.

About halfway over, with one side of the boat 10 feet straight up in the air and stuck, I called Johnnie for some help.  I had one side of the boat stuck in the dirt and the other side stuck on the A frame.

John came over and promptly told me to cut off about a foot of my 2x6 boards that were bolted across the gunnels and were currently dug into the ground.  A few minutes later with the help of Mr. Sawzall, the boards were cut, the boat was free and setting on the jig, right side up!







Saturday, November 10, 2012

I finally got the boat painted!

Well after about a month of weather delays, yesterday I got the boat painted.  I faired the boat as smooth as I was willing to go with it.  I used epoxy with microballons added as a filler.  Then I sanded, filled, sanded, filled.......Sprayed a heavy high build epoxy primer....Sanded, filled...Sprayed more high build epoxy primer....Sanded filled and sanded.

Here is the paint I used to cover the boat with.  Dupont's Imron.  I used the Imron 3.5 HG version.  This paint is an industrial coating designed for firetrucks, 18 wheelers, airplanes, buildings, bridges, marine structures.  The paint is very easy to work with, and very forgiving regarding temperatures and environment.   Subsequent coats burn into previous coats very easily, much like the old school lacquers.

The biggest drawback is the hazard from the fumes.  The VOC's in this paint are very nasty.  There are rumors that persons exposed to the fumes without protection have about a 20% chance of getting chemical induced asthma!  Needless to say, I wore a 3M respirator mask designed just for this purpose with Organic Vapor cartridges.  Here are the cartridges after spraying the green paint.
This 3m respirator worked fantastic, I could not smell ANY paint fumes while wearing it.  If you spray paint, get one of these!

First I put on the very bottom color, the part that will be under the water.  It is a nice light beige / cream color.  It is kind of hard to see in these pictures.

Next I masked off the waterline with the 3M green masking tape, then masked off the cream colored area with masking paper.

I put three coats of paint on the boat.  It took about 1 1/2 gallons of cream color, and about 1 1/3 gallons of the green color to paint three coats.

Now I just have to wait about a week for the paint to cure really hard, then we are going to flip this thing over and build the inside!